Viglen Ethergen PnP 2000A - Revision history

Malvineous: Update infobox

2016-02-13T07:12:57Z

Update infobox

← Older revision		Revision as of 07:12, 13 February 2016
Line 1:		Line 1:
	{{~~Ethernet~~ Infobox		{{Device Infobox/Begin
	\| Bus type = ISA		\| Bus type = ISA
	\| Bus width = 16-bit		\| Bus width = 16-bit
Line 8:		Line 8:
	\| Compatible with = [[Has compatibility::NE1000]], [[Has compatibility::NE2000]]		\| Compatible with = [[Has compatibility::NE1000]], [[Has compatibility::NE2000]]
	\| Connectors = [[Has connector::TP]], [[Has connector::BNC]]		\| Connectors = [[Has connector::TP]], [[Has connector::BNC]]
			\| Requires -5VDC = No
			\| Requires -12VDC = No
			\| Config = [[Config method::Software]] or [[Config method::PnP]]
			}}
			{{Device Infobox/Ethernet
	\| Is ROM socketed = Yes		\| Is ROM socketed = Yes
	\| ROM type = 28-pin JEDEC		\| ROM type = 28-pin JEDEC
	\| Is ROM writable = No		\| Is ROM writable = No
	~~\| Requires -5VDC = Unknown~~		}}
	~~\| Requires -12VDC = Unknown~~		{{Device Infobox/End
	~~\| Config = [[Config method::Software]] or [[Config method::PnP]]~~
	\| Driver = [http://www.vogonsdrivers.com/getfile.php?fileid=902 Vogonsdrivers]		\| Driver = [http://www.vogonsdrivers.com/getfile.php?fileid=902 Vogonsdrivers]
	}}		}}

Malvineous: Add driver URL

2016-02-05T12:36:12Z

Add driver URL

← Older revision		Revision as of 12:36, 5 February 2016
Line 14:		Line 14:
	\| Requires -12VDC = Unknown		\| Requires -12VDC = Unknown
	\| Config = [[Config method::Software]] or [[Config method::PnP]]		\| Config = [[Config method::Software]] or [[Config method::PnP]]
	\| Driver = ~~viglen~~/~~VE20005~~.~~ZIP~~		\| Driver = [http://www.vogonsdrivers.com/getfile.php?fileid=902 Vogonsdrivers]
	}}		}}

Malvineous: Update infobox

2016-01-24T04:18:42Z

Update infobox

← Older revision		Revision as of 04:18, 24 January 2016
Line 1:		Line 1:
	{{Ethernet Infobox		{{Ethernet Infobox
	\| ~~Card~~ type = 16-bit ~~ISA~~		\| Bus type = ISA
			\| Bus width = 16-bit
			\| Bus speed = 8 MHz
	\| 8-bit ISA compatible = Yes		\| 8-bit ISA compatible = Yes
	\| Manufacturer = Viglen		\| Manufacturer = Viglen

Malvineous: Add connectors

2016-01-23T23:21:47Z

Add connectors

← Older revision		Revision as of 23:21, 23 January 2016
Line 5:		Line 5:
	\| Chipset = UK0023A		\| Chipset = UK0023A
	\| Compatible with = [[Has compatibility::NE1000]], [[Has compatibility::NE2000]]		\| Compatible with = [[Has compatibility::NE1000]], [[Has compatibility::NE2000]]
			\| Connectors = [[Has connector::TP]], [[Has connector::BNC]]
	\| Is ROM socketed = Yes		\| Is ROM socketed = Yes
	\| ROM type = 28-pin JEDEC		\| ROM type = 28-pin JEDEC

Malvineous: Document card

2016-01-23T12:49:33Z

Document card

New page

{{Ethernet Infobox
| Card type = 16-bit ISA
| 8-bit ISA compatible = Yes
| Manufacturer = Viglen
| Chipset = UK0023A
| Compatible with = [[Has compatibility::NE1000]], [[Has compatibility::NE2000]]
| Is ROM socketed = Yes
| ROM type = 28-pin JEDEC
| Is ROM writable = No
| Requires -5VDC = Unknown
| Requires -12VDC = Unknown
| Config = [[Config method::Software]] or [[Config method::PnP]]
| Driver = viglen/VE20005.ZIP
}}

The '''Viglen Ethergen PnP 2000A''' is a 10Mbps ISA network card. It can be configured in either Plug-n-Play mode (which requires a PnP BIOS or configuration manager) or jumperless mode, where the base address, IRQ and other settings are changed via the manufacturer's configuration utility and no PnP manager is required.

== Additional photos ==

<gallery mode="packed">
Image:Viglen Ethergen PnP 2000A underside.jpg|Underside
Image:Viglen Ethergen PnP 2000A configuration utility.png|Config utility
Image:Viglen Ethergen PnP 2000A diagnostics.png|Diagnostics
</gallery>

== Boot ROM ==

[[Image:{{PAGENAME}} boot ROM settings.png|thumb|right|Boot ROM address options]]

This card's boot ROM socket will take a standard 28-pin ROM chip. It has also been successfully tested with a 32-pin ROM chip using an adapter<ref>[http://sbfmdrv.blogspot.com.au/2015/11/retrofitting-new-eeprom-into-old-pc.html Port 388h - Retrofitting a new EEPROM into an old PC]</ref>. XTIDE will run without any problem.

The card's DOS drivers come with a configuration program (<tt>DIAG/SETUP.EXE</tt>) that can be used to enable the ROM socket (it is disabled by default) and set the base address, as well as adjust all the usual options like I/O address and IRQ.

If shadow RAM is active, the configuration utility will report all shadowed blocks of memory as in-use, and will force you to choose a different address. This means every time the utility loads while shadow RAM is enabled, it will force the boot ROM's address to be moved. Once the address has been set however, shadow RAM can be re-enabled without any problem.

== Resources ==

* I/O address: 220, 240, 260 ... 3C0, 3E0.
* IRQ: 2/9, 3, 4, 5, 10, 11, 12, 15.
* Boot ROM: C000, C400, C800 ... D800, DC00, Disabled.

IRQs 10+ are only available in 16-bit slots, however even when the card is in a 16-bit slot it often seems to be stuck in 8-bit mode according to the diagnostics, meaning IRQs 10+ are never allowed to be chosen (tested in a Headland HT12 286 motherboard.)

== Card family ==

The following explanation was taken from the Viglen website<ref>[http://download.viglen.co.uk/files/Network_Cards/Viglen/Ethergen_2000A/WHICH1.TXT which1.txt]</ref>.

<pre>
It may be required to determine the Network card for a given Driver,
this may help.............

Quick "General" History
-----------------------

Version 1 " our first card ".
This card had quite a large circuit board with the following Part number printed on the board
P/N : 142640-420 REV: 01E
Driver VE20001.ZIP

Version 1b
Has small circuit board.
P/N : 142640-406 REV: 01
Driver VE20001.ZIP

Version 1c
Has small circuit board.
P/N : 145640-006
Driver VE20001.ZIP

Note
****
If the setup program from any other disk is run prior to the version 1 setup disk,
configuration problems can occur.
To resolve this, make sure the PC is warm or cold booted before running setup.

Version 2
The card had a much smaller circuit board with the following part number
P/N : 142640-403 REV: 01A
Driver VE20002.ZIP

Version 3
Another card with a small circuit board as well as the new " YES NetWare Tested and Approved " sticker
which is now being shipped as standard.
There are two orange capacitors at position c32 and c31
P/N : 142651-400 REV : 01
Driver VE20003.ZIP

Version 4
This is actually Version 2 with the " YES NetWare Tested and Approved " sticker slapped on.
P/N : 14260-403 REV: 01A
Driver as above version 2

Version 5
This is the newer Viglen Ethergen Plug & play 2000A
P/N : 142066 400 REV 02A
Driver VE20005.ZIP

A last Note..
Sometimes the wrong driver disk has gone out with these cards.
Here is a guide

Version 1 disk label number 146929-008 Green Band configured by running a:\diag\setup
Version 1b - as above
Version 2 disk label number 146209-008 Purple Band configured by running a:\diag\setup
Version 3 disk label number 146211-008 Yellow Band configured by running a:\setup
Version 4 disk label number 146209-008 Purple Band configured by running a:\diag\setup

Thanks for listening.
</pre>

== References ==

<references/>