Difference between revisions of "Accton EN1640"
From Vogons Wiki
Malvineous (Talk | contribs) (Update infobox) |
Malvineous (Talk | contribs) (Update infobox) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | {{Device Infobox/Begin |
| Bus type = ISA | | Bus type = ISA | ||
| Bus width = 16-bit | | Bus width = 16-bit | ||
| Line 8: | Line 8: | ||
| Compatible with = [[Has compatibility::NE1000]], [[Has compatibility::NE2000]] | | Compatible with = [[Has compatibility::NE1000]], [[Has compatibility::NE2000]] | ||
| Connectors = [[Has connector::AUI]], [[Has connector::BNC]] | | Connectors = [[Has connector::AUI]], [[Has connector::BNC]] | ||
| + | | Requires -5VDC = No | ||
| + | | Requires -12VDC = No | ||
| + | | Config = [[Config method::Software]] | ||
| + | }} | ||
| + | {{Device Infobox/Ethernet | ||
| Is ROM socketed = Yes | | Is ROM socketed = Yes | ||
| ROM type = 28-pin JEDEC | | ROM type = 28-pin JEDEC | ||
| Is ROM writable = No | | Is ROM writable = No | ||
| − | + | }} | |
| − | + | {{Device Infobox/End | |
| − | | | + | | Driver = [http://www.vogonsdrivers.com/getfile.php?fileid=900 Vogonsdrivers] |
| − | + | ||
}} | }} | ||
| Line 23: | Line 27: | ||
<gallery mode="packed"> | <gallery mode="packed"> | ||
Image:Accton EN1640 underside.jpg|Underside | Image:Accton EN1640 underside.jpg|Underside | ||
| + | Image:Accton EN1640 configuration utility.png|Config utility | ||
| + | Image:Accton EN1640 diagnostics.png|Diagnostics | ||
| + | Image:Accton EN1640 configuration options.png|Config options | ||
</gallery> | </gallery> | ||
| Line 30: | Line 37: | ||
The card's DOS drivers come with a configuration program (<tt>DIAG/SETUP.EXE</tt>) that can be used to enable the ROM socket (it is disabled by default) and set the base address, as well as adjust all the usual options like base address and IRQ. | The card's DOS drivers come with a configuration program (<tt>DIAG/SETUP.EXE</tt>) that can be used to enable the ROM socket (it is disabled by default) and set the base address, as well as adjust all the usual options like base address and IRQ. | ||
| + | |||
| + | == Resources == | ||
| + | |||
| + | * I/O address: 0, 20, 40, ... 3A0, 3E0, then the same increments starting at 2000, 4000, 6000, 8000, A000, C000, E000. | ||
| + | * IRQ: 2, 3, 4, 5, 7, 10, 11, 15, Disabled. | ||
| + | * Boot ROM size: 16kB, 32kB, 64kB, Disabled. | ||
| + | * Boot ROM: 8000, 8400, 8800, 8C00, then the same increments starting at 9000, A000, B000, C000, D000, E000 and F000. | ||
== References == | == References == | ||
<references/> | <references/> | ||
Latest revision as of 18:09, 13 February 2016
Accton EN1640
| Bus type | ISA |
|---|---|
| Bus width | 16-bit |
| Bus speed | 8 MHz |
| 8-bit ISA compatible? | Yes |
| Manufacturer | Accton Technology Corporation |
| Chipset | EN50903 |
| Compatible with | NE1000, NE2000 |
| Connectors | AUI, BNC |
| Requires -5VDC? | No |
| Requires -12VDC? | No |
| Config method | Software |
| Ethernet | |
| Boot ROM | Socket, 28-pin JEDEC, read-only |
| Driver | Vogonsdrivers |
The Accton EN1640 is a 10Mbps network card.
Additional photos
Underside
Config utility
Diagnostics
Config options
Boot ROM
This card's boot ROM socket will take a standard 28-pin ROM chip. It has also been successfully tested with a 32-pin ROM chip using an adapter[1]. XTIDE will run without any problem.
The card's DOS drivers come with a configuration program (DIAG/SETUP.EXE) that can be used to enable the ROM socket (it is disabled by default) and set the base address, as well as adjust all the usual options like base address and IRQ.
Resources
- I/O address: 0, 20, 40, ... 3A0, 3E0, then the same increments starting at 2000, 4000, 6000, 8000, A000, C000, E000.
- IRQ: 2, 3, 4, 5, 7, 10, 11, 15, Disabled.
- Boot ROM size: 16kB, 32kB, 64kB, Disabled.
- Boot ROM: 8000, 8400, 8800, 8C00, then the same increments starting at 9000, A000, B000, C000, D000, E000 and F000.
