Difference between revisions of "GoldStar Prime 2C MKIII"
From Vogons Wiki
Malvineous (Talk | contribs) (Basic info) |
Malvineous (Talk | contribs) (Update infobox) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | {{Device Infobox/Begin |
| Bus type = ISA | | Bus type = ISA | ||
| Bus width = 16-bit | | Bus width = 16-bit | ||
| Line 8: | Line 8: | ||
| Compatible with = [[Has compatibility::IDE]], [[Has compatibility::PC Floppy]], [[Has compatibility::RS232]], [[Has compatibility::LPT]], [[Has compatibility::Gameport]] | | Compatible with = [[Has compatibility::IDE]], [[Has compatibility::PC Floppy]], [[Has compatibility::RS232]], [[Has compatibility::LPT]], [[Has compatibility::Gameport]] | ||
| Connectors = [[Has connector::RS232/DB9]], [[Has connector::LPT]] <!-- Other connectors aren't shipped with the card so aren't included --> | | Connectors = [[Has connector::RS232/DB9]], [[Has connector::LPT]] <!-- Other connectors aren't shipped with the card so aren't included --> | ||
| − | | | + | | Requires -5VDC = No |
| + | | Requires -12VDC = Yes | ||
| + | | Config = [[Config method::Jumpers]] | ||
| + | }} | ||
| + | {{Device Infobox/IO | ||
| Serial ports = 2 | | Serial ports = 2 | ||
| + | | UART = | ||
| + | | COM1 = Yes | ||
| + | | COM2 = Yes | ||
| + | | COM3 = Yes | ||
| + | | COM4 = Yes | ||
| Parallel ports = 1 | | Parallel ports = 1 | ||
| + | | Bi-dir = | ||
| + | | ECP = | ||
| + | | EPP = | ||
| + | | LPT1 = Yes | ||
| + | | LPT2 = Yes | ||
| + | | LPT3 = No | ||
| + | | LPT4 = No | ||
| Game ports = 1 | | Game ports = 1 | ||
| + | }} | ||
| + | {{Device Infobox/Floppy Controller | ||
| Floppy buses = 1 | | Floppy buses = 1 | ||
| − | | Secondary | + | | Drives per bus = 2 |
| + | | Secondary = Yes | ||
| + | | ROM type = None | ||
| + | }} | ||
| + | {{Device Infobox/IDE Controller | ||
| IDE buses = 1 | | IDE buses = 1 | ||
| − | | | + | | Primary = Yes |
| − | | | + | | Secondary = Yes |
| − | | | + | | Tertiary = No |
| − | | | + | | Quaternary = No |
| + | | ROM type = None | ||
| + | }} | ||
| + | {{Device Infobox/End | ||
| Driver = N/A | | Driver = N/A | ||
}} | }} | ||
| Line 26: | Line 51: | ||
The card's part number is P2C94002. | The card's part number is P2C94002. | ||
| − | The TH99 entry | + | The TH99 entry has some mistakes, such as a jumper toggling between "primary IDE enabled" or "secondary IDE disabled". Since there is already a separate jumper to enable/disable the IDE interface, this is actually meant to switch the interface between primary and secondary when it is enabled. The same goes for the floppy interface. |
| + | |||
| + | This card is notable because the serial ports can be set to use IRQs 5 and 9, which will prevent them from conflicting with the default IRQs of 4 and 3, should the card be added as an additional controller. | ||
| + | |||
| + | The pinout for the serial headers is currently unknown. There are two types in common use. This page should be updated when the correct type is known. | ||
== Additional photos == | == Additional photos == | ||
Latest revision as of 17:12, 13 February 2016
GoldStar Prime 2C MKIII
| Bus type | ISA |
|---|---|
| Bus width | 16-bit |
| Bus speed | 8 MHz |
| 8-bit ISA compatible? | |
| Manufacturer | GoldStar |
| Chipset | GoldStar Prime 2C |
| Compatible with | IDE, PC Floppy, RS232, LPT, Gameport |
| Connectors | RS232/DB9, LPT |
| Requires -5VDC? | No |
| Requires -12VDC? | Yes |
| Config method | Jumpers |
| IO Controller | |
| Serial ports | 2 |
| UART | |
| COM1/2/3/4? | Yes / Yes / Yes / Yes |
| Parallel ports | 1 |
| Bi-dir? | |
| ECP? | |
| EPP? | |
| LPT1/2/3/4? | Yes / Yes / No / No |
| Game ports | 1 |
| Floppy Controller | |
| Floppy buses | 1 |
| Drives per bus | 2 |
| Secondary? | Yes |
| ROM type | None |
| IDE Controller | |
| IDE buses | 1 |
| Primary? | Yes |
| Secondary? | Yes |
| Tertiary? | No |
| Quaternary? | No |
| ROM type | None |
| Driver | N/A |
The GoldStar Prime 2C MKIII is a Super I/O board from GoldStar using their own chipset.
The card's part number is P2C94002.
The TH99 entry has some mistakes, such as a jumper toggling between "primary IDE enabled" or "secondary IDE disabled". Since there is already a separate jumper to enable/disable the IDE interface, this is actually meant to switch the interface between primary and secondary when it is enabled. The same goes for the floppy interface.
This card is notable because the serial ports can be set to use IRQs 5 and 9, which will prevent them from conflicting with the default IRQs of 4 and 3, should the card be added as an additional controller.
The pinout for the serial headers is currently unknown. There are two types in common use. This page should be updated when the correct type is known.
Additional photos
Underside
Related links
- FCC ID is JGBPRIME2C
- TH99
