Difference between revisions of "Creative Sound Blaster 32 PnP"
Malvineous (Talk | contribs) (Rename Dupont connectors) |
Malvineous (Talk | contribs) (Add note about secondary IDE issues) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 28: | Line 28: | ||
{{Device Infobox/IDE Controller | {{Device Infobox/IDE Controller | ||
| IDE buses = 1 | | IDE buses = 1 | ||
| + | | Primary = N | ||
| + | | Secondary = Y | ||
| + | | Tertiary = Y | ||
| + | | Quaternary = Y | ||
| ROM type = None | | ROM type = None | ||
}} | }} | ||
| Line 36: | Line 40: | ||
The '''Sound Blaster 32 PnP''' is an update to the Sound Blaster 16 with the ''WavEffects'' (EMU8000) chip from the [[Creative Sound Blaster AWE32|AWE32]]. It is one of the few Creative Labs cards that can take standard 30-pin SIMMs to increase the memory available for MIDI instrument samples. | The '''Sound Blaster 32 PnP''' is an update to the Sound Blaster 16 with the ''WavEffects'' (EMU8000) chip from the [[Creative Sound Blaster AWE32|AWE32]]. It is one of the few Creative Labs cards that can take standard 30-pin SIMMs to increase the memory available for MIDI instrument samples. | ||
| − | It is very similar to the [[Creative Sound Blaster AWE32 PnP (IDE)]], but with a CT1749 instead of the CT8903 (AWE32) chip. It also has a SPDIF output connector, which the AWE32 does not. | + | It is very similar to the [[Creative Sound Blaster AWE32 PnP (IDE)]], but with a CT1749 instead of the CT8903 (AWE32) chip. It also has a SPDIF output connector, which the AWE32 does not. The SB32 series also has no onboard memory, while the AWE32 has 512 kB. |
== Additional photos == | == Additional photos == | ||
| Line 43: | Line 47: | ||
Image:Creative Sound Blaster 32 PnP underside.jpg|Underside | Image:Creative Sound Blaster 32 PnP underside.jpg|Underside | ||
</gallery> | </gallery> | ||
| + | |||
| + | == IDE interface == | ||
| + | |||
| + | While the PnP nature of the card allows the IDE interface to be configured on a wide variety of ports (allowing even more than four IDE interfaces in a single system), one caveat applies. When the card is configured as a secondary IDE controller, the second group of I/O addresses is truncated. Normally the second IDE controller also uses ports 376-377, however this can conflict with the floppy controller, so the PnP settings only reserve port 376. In this case, some CD-ROM device drivers (such as [[VIDE-CDD.SYS]]) will not recognise the interface. Because of this, setting the card to the secondary IDE interface is not recommended. It works well as the third or fourth IDE interface as the ports are not truncated with these settings. | ||
Latest revision as of 12:04, 26 February 2017
| Bus type | ISA | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bus width | 16-bit | ||||||||||||||||
| Bus speed | 8 MHz | ||||||||||||||||
| 8-bit ISA compatible? | |||||||||||||||||
| Manufacturer | Creative Labs | ||||||||||||||||
| Chipset | CT1749 | ||||||||||||||||
| Compatible with | Sound Blaster, 30-pin SIMM | ||||||||||||||||
| Connectors | Mic, Line in, Line out, Speaker out, Gameport | ||||||||||||||||
| Requires -5VDC? | No | ||||||||||||||||
| Requires -12VDC? | Yes | ||||||||||||||||
| Config method | PnP | ||||||||||||||||
| Audio | |||||||||||||||||
| Model | CT3620 | ||||||||||||||||
| Full duplex | Unknown | ||||||||||||||||
| Max sample rate | Unknown | ||||||||||||||||
| Channels | 2 | ||||||||||||||||
| FM synth | CQM | ||||||||||||||||
| Internal connectors |
|
||||||||||||||||
| Factory memory | Unknown | ||||||||||||||||
| Max memory | 28MB 29,360,128 B |
||||||||||||||||
| CD interface | IDE | ||||||||||||||||
| IDE Controller | |||||||||||||||||
| IDE buses | 1 | ||||||||||||||||
| Primary? | N | ||||||||||||||||
| Secondary? | Y | ||||||||||||||||
| Tertiary? | Y | ||||||||||||||||
| Quaternary? | Y | ||||||||||||||||
| ROM type | None | ||||||||||||||||
| Driver | Missing download URL | ||||||||||||||||
The Sound Blaster 32 PnP is an update to the Sound Blaster 16 with the WavEffects (EMU8000) chip from the AWE32. It is one of the few Creative Labs cards that can take standard 30-pin SIMMs to increase the memory available for MIDI instrument samples.
It is very similar to the Creative Sound Blaster AWE32 PnP (IDE), but with a CT1749 instead of the CT8903 (AWE32) chip. It also has a SPDIF output connector, which the AWE32 does not. The SB32 series also has no onboard memory, while the AWE32 has 512 kB.
Additional photos
- Creative Sound Blaster 32 PnP underside.jpg
Underside
IDE interface
While the PnP nature of the card allows the IDE interface to be configured on a wide variety of ports (allowing even more than four IDE interfaces in a single system), one caveat applies. When the card is configured as a secondary IDE controller, the second group of I/O addresses is truncated. Normally the second IDE controller also uses ports 376-377, however this can conflict with the floppy controller, so the PnP settings only reserve port 376. In this case, some CD-ROM device drivers (such as VIDE-CDD.SYS) will not recognise the interface. Because of this, setting the card to the secondary IDE interface is not recommended. It works well as the third or fourth IDE interface as the ports are not truncated with these settings.
